How To Power Wash A Trex Deck

April 17, 2022 Post a Comment

Take a look at the steps below. Never use a chlorine bleach based deck cleaner.

Spray & Clean Composite Deck Cleaner in 2020 Deck

(trex doesn't specify a brand of soap, so a dish soap such as dawn is a good choice.)

How to power wash a trex deck. Be consistent in the length when you tip it from the surface. Dip a nylon scrub brush into the water and oxiclean mixture and scrub it over the deck. Continue across the deck until the entire unit is cleaned to your satisfaction.

The next step is to seal the deck. Start with the pressure at 500 to 600 psi and test it on an inconspicuous area. Be sure to shovel parallel to the direction the boards are laid.

One may be wondering if a deck with treated wood should still have a sealant used. The process should not harm your trex deck in the least. Engage the trigger while holding the wand tip a couple of feet away from the deck surface, then lower the wand closer as needed.

If you need to remove mold and mildew from your trex deck, it's a fairly simple process. You should pressure wash the deck from a distance of at least 36 inches. After being pressure washed, the wood will be in need of a water sealant.

The biggest issue with power washing is the pressure. We soft wash the boards, using lower pressure to avoid damaging the finish. Learn how to clean and care for your composite decking by reading the information that applies to your decking product and get ready to enjoy maximum outdoor living with minimal maintenance.

Increase the pressure incrementally as needed to clean the deck without damaging or etching the wood surface. When power washing your deck, direct the spray to match the grain. A 40 o to 60 o (degree) tip size is standard for cleaning a deck.

Do always test a small area first to be sure though. Additionally, can i power wash my composite deck? Do not use a wire brush as that will thoroughly scratch your plastic decking.

This helps prevent accidentally scoring or marking the surface by going against the grain or by crossing over several boards. When cleaning a wood deck, we apply a natural solution that opens the pores and moves with the grain of the wood in wide sweeping motions as we power wash. The answer is yes, the deck should still have a sealant applied.

Spray the deck with a hose to remove surface dirt and debris. This constancy will prevent lap marks. Use of products containing bleach or acid will lighten the surface of trex.

(trex doesn’t specify a brand of soap, so a dish soap such as dawn is a good choice.) the brush will ensure you’ll get any dirt in the. For more information on power washing your deck, please click this link to watch our video. How to clean trex decking.

Spray the deck with a hose to remove surface dirt and debris. Begin “sweeping” the deck from the house side out. To power wash a composite deck, spray deck with soap, then follow by gently scrubbing each deck board with a soft bristle brush.

If you choose to scrub the deck clean, choose a deck brush with natural or plastic bristles. The use of products containing bleach or acid will lighten the surface of trex. Mix a solution of 2 parts of vinegar and 1 part of water in a bucket.

Use a pressure washer to remove as much of the mold as possible. Spray/rinse each deck board using a fan tip no closer than 8″ from the decking surface and rinse thoroughly, as dirty water from cleaning left to dry will cause a film to remain on the decking surface. If your deck was built with trex’s enhance, select or transcend decking, this is what you should do:

This is for your safety and the quality of your deck. If you need to shovel snow off of your deck, gently use a plastic shovel or a broom to remove snow. Power wash deck surfaces safely instead of letting mold and mildew grow uncontrollably, treat your deck to routine maintenance by a professional power washing service.

Another homemade method for deck wash soap is using half a cup of white vinegar and ¼ cup of baking soda with 1 gallon of water, which is good for mold and mildew. Use a broom to remove snow from your composite decking. Consequently, what can i use to clean a trex deck?

When choosing a professional to power wash your deck, don’t just choose someone from your local power washing company—choose someone who specifically has experience power washing decks. Pour the solution on the mold and sprinkle baking soda all over the area. For example, the pros at perfect power wash use a soft wash method designed to combine biodegradable cleansers with safe pressure to ensure the best results for your deck.

Bring the fan to the surface where you want to sweep the deck. A pressure washer should only be used on transcend, select or enhance decks. Clean with the grain of the individual boards.

Severe Mold Mildew Algae